Hinge Box
Lid options
Five kinds of lid (open, fixed, lift-off, flip-top and cap), steps, windows, holes and the lip under a removable lid.
- Open tray: no lid. Fixed lid: glued on the wall's top tabs. Removable lid: lifts off, with a lip that drops inside the walls.
- Flip-top lid: one plate with a living-hinge band across it. The strip between the band and the hinge side is held by the wall's top tabs; the rest is a flap that swings up as the band bends. Pick the hinge side (back for a flip-top box, left for a cabinet door). The band is sized to open about 105°; a wider band opens further. The panel tells you how far it opens.
- Cap lid: a shallow box of its own that slips over the top, like a shoebox or hat-box lid. Cap height sets how far it comes down. Its walls are shorter than the box's, so when the box's hinge is too stiff for them they get their own fitted lattice.
- Steps: up to three smaller plates stacked on a fixed, lift-off or cap lid, for a stepped or domed top. Step size is how much smaller each one is all round. A cylinder's steps are round.
- Overhang: the lid reaches this far past the walls all round, so a flat top has an edge to lift by. 0 keeps it flush with the box.
- Rim and clear window: a rim cuts the lid's middle away; turn on Clear window for a clear acrylic plate under it, for a display box or a display cabinet. Cut the window from 2 to 3 mm clear acrylic.
- Lamp hole: a 40 mm hole for an E27 lamp holder (set 29 mm for E14), for a pendant shade.
- Hole: a finger hole (about 22 mm) to lift a removable lid, or a knob hole sized for your knob's screw. A hole too big for the lid is left out, and Checks says so.
- Lip under the lid (removable lids): a second plate that sits inside the walls and keeps the lid in place. Turn it off for a lid that simply rests on top.
- Tissue and coin slots: a long slot with round ends along the box's long side, sized to the box (tissue) or 32 × 4 mm (coin). Set its length and width; a slot too big for the lid is left out.
- Score the lip on the lid: marks where the lip goes, so it lines up when you glue it. Put the scored side down.
Options
- Overhang0 to 100 mm · step 0.5 mm
- How far the lid reaches past the walls all round, for a flat top with an edge to lift. 0 keeps the lid flush.
- Hinge band4 to 300 mm · step 0.5 mm
- How wide a flip lid's living-hinge band is. A wider band opens further before it is bent to its limit; left out, it is sized to open about 105°.
- Fixed strip3 to 200 mm · step 0.5 mm
- The strip between a flip lid's hinge band and its edge, held by the wall's top tabs. Left out, it is just wide enough for the tab slots.
- Cap height12 to 3000 mm · step 1 mm
- How far a cap lid comes down over the box, its top included. Left out, it is 40% of the box, 25 to 60 mm.
- Steps0 to 3 · step 1
- How many smaller plates are stacked on the lid, each glued on the one below, for a stepped or domed top.
- Step size1 to 60 mm · step 0.5 mm
- How much smaller each step is than the one under it, all round.
- Hole size1 to 500 mm · step 0.5 mm
- The diameter of the lid's hole: about 22 mm for a fingertip, or the size of your knob's screw. For a tissue or coin slot, the slot's length.
- Slot width1 to 200 mm · step 0.5 mm
- How wide the tissue or coin slot is. About 25 to 35 mm lets tissues pull through; 3 to 4 mm takes coins. For a rim, how wide the frame left round the open top is.